set
set adf <num>
Set ADF to <num> frequency in a flight plan
set afcontrol <plane><helicopter>
atmospheric rudder control by user on or off. Set off if your flight plan wants to take the stick.
set altitude [alt] <num>
preselect target altitude (m)
set apcontrol <plane> or <helicopter>
Toggle autopilot modes between plane and helicopter
set apmode airfoil
set autopilot control to rudder
set approachentryaltitude <num>
Define the altitude above ground (ground is provided by FSP) to be automatically entered as target altitude when switching to the approach entry point
set approachentrydistance <num>
Define the distance, at which the approach entry point is generated from runway start of selected runway. <num> is distance in nm
set approachentryoffset <num>
Define the angle from runway inbound heading, at which the approach entry point is generated. <num> is offset in deg
set brakepower <num>
sets brakepower to <num> percent (0-100) .Value only valid for this session.
set climb [desc] <num>
preselect climb / sink rate (m/s)
set climb [desc] autoclimb [ac]
preselect autoclimb; set climb rates automatically
set climb [desc] autodescend [ad]
preselect autodescend; set descent rates automatically
set climb wp
set the climb rate to a value that the predefined altitude is hit at the next waypoint
set cmdonly on
if used in the beginning of the flight plan, all actual flying has to be done by the pilot itself
set cmdonly off
switch cmdonly mode off in a flight plan
set com [com1] <num>
Set com1 to <num> frequency in a flight plan
set current utc
set current utc time
set destination <ICAO>
set destination airport
set departure [dep] <ICAO>
set departure airport
set distanceunits <miles><meters>
define units for distances in your flight plan
set fuelpercent <num>
sets fuel level in all tanks to <num> percent
set gear
gear down during auto landings. Disables “set nogear”. Use “set nogear” to perform auto landings without gear down (waterlandings)
set home airport
Looks up nearest airport and sets it as the home airport for later use. Usually defined on ground at the beginning of a flight plan.
set ils
Set vertical autopilot into the approach mode - equivalent to pressing the ALT and the APR button on the EFIS
set ilsentrydistance <num>
Define the distance, at which the ils entry entry point is generated from runway start of selected runway. <num> is distance in nm
set maxbank <num>
Set maximum bank angle that FSP uses to turn into a target. 50 would be fighter style (small radius), 25 would be passenger jet style (big radius)
set maxpitch <num>
Set maximum pitch angle that FSP uses to archieve a climb / sink rate
set nav1 <num>
Set nav1 to <num> frequency in a flight plan, f.e. 118.70
set nav2 <num>
Set nav2 to <num> frequency in a flight plan.
set nogear
In planes with floats and wheels, wheels will not be lowered during auto landings. Use “set gear” to switch off.
set origin <ICAO>
set origin airport
set payload <num>
set payload to <num> pounds evenly distributed between all payloadstations of the aircraft
set payloadstation <which> <what>
set payloadstation <which> of current plane with <what> pounds of payload
set radarrange <num>
define the radarrange in the efis to <num> miles
set speed <num>
Set speed value in knots or mach, as required
set speed minimumspeed
as defined in fspilot.ini
set speed approachspeed
as defined in fspilot.ini
set speed cruisingspeed
as defined in fspilot.ini
set speed takeoffspeed
as defined in fspilot.ini
set speed safespeed
Sets an effective cruising speed depending on altitude and aircraft. < FL100: 250 knt; between FL 100 and 180:barberpolespeed* 0.88; > FL 180: barberpolemach * 0.88
set speedunits <knots><meters>
define the units for speed in your flight plan
set throttle <num>
sets the throttle levers to [num] percent
set timeacceleration [timeacc] <num>
speed up or reduce time acceleration within a flight plan
set userinput <on><off>
Enable userinput during a flight plan. Otherwise, pressing buttons on the EFIS will be disabled except the screenshot button.
set waypointclimb <num>
Defines the climbrate in ft/min in which the aircraft will climb between waypoints.
set wphitprecision <num1> <num2>
Define the distance at which FSP switches to the next target (waypoint) in flight plans. <num1> distance below FL 100 in meters, <num2> sistance above FL100 in meters. Both arguments mandatory.
set xpndr [transponder] <num>
Set the transponder to <num> frequency in a flight plan
Created with the Personal Edition of HelpNDoc: Easily create EBooks